Agilent Technologies HP 54601B Podręcznik Użytkownika Strona 19
- Strona / 123
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
2 Press Print/Utility .
If the Previous Menu softkey appears on the rightmost softkey,
press
Print/Utility again.
When the module is installed, an additional softkey appears at the second
softkey from the left. For the HP 54655A, the label is HP-IB Menu. For the
HP 54656A, the label is RS-232 Menu.
3 Press the HP-IB Menu softkey or the RS-232 Menu softkey.
For HP 54655A, a softkey menu with five choices appears. Four of them are
related to the configuration of the HP-IB interface.
•
Connect to Selects the device connected to the oscilloscope.
Selections include HP plotter, HP printer, and computer.
•
Factors Selects whether the printer or plotter output contains the
information concerning the basic settings of the oscilloscope.
•
Resolution Selects the resolution of the printer or plotter output.
•
Address Selects the HP-IB address of the instrument. Valid addresses
range from 0 to 30. To change the address, press the softkey or turn the
knob closest to the Cursors key.
•
Previous Menu Returns the oscilloscope to the previous softkey menu.
For HP 54656A, a softkey menu with six choices appears. Five of them are
related to the configuration of the RS-232 interface.
•
Connect to Selects the device that the oscilloscope is connected to.
Selections include HP plotter, HP printer, Epson compatible printer, and
computer.
•
Factors Selects whether the printer or plotter output contains the
information concerning the basic settings of the oscilloscope.
•
Resolution Selects the resolution of the printer or plotter output.
•
Baud Rate Selects the baud rate of the RS-232 port. Valid baud rates
are 1200, 2400, 9600, and 19200.
•
Handshake Selects the handshaking method used in the RS-232. DTR
refers to the hardware handshaking using the DTR signal line. XON refers
to the software handshaking using the XON/XOFF protocol.
•
Previous Menu Returns the oscilloscope to the previous softkey menu.
Operating the Test Automation Module
To configure the interface
18
- HP 54655A and 2
- HP 54656A Test 2
- Automation Modules 2
- In This Book 5
- Contents 6
- 3 Solutions 7
- 4 Test Sequencing Programming 7
- 5 Reference Information 7
- Quick Start 10
- Turn off the oscilloscope 12
- 1 . Then 13
- Autoscale 13
- Print/Utility 13
- Press Setup 15
- Operating the Test 16
- Automation Module 16
- To configure the interface 18
- Press Print/Utility 19
- Print with Factor ON 20
- Figure 3 21
- Module memories 23
- To create a setup sequence 27
- To execute a sequence 28
- Print/Utility twice 29
- Autostore 30
- Autostore again 30
- To spot the failure area 38
- To define action messages 39
- Label ** Test #xx ** 40
- Pass PASS 40
- Fail Min FAIL 40
- Fail Max FAIL 40
- Output 1 PASS 47
- Output 2 FAIL 47
- Output 3 OFF 47
- Output 4 OFF 47
- Output 5 OFF 47
- Sequence step configuration 52
- To copy a step or a mask 54
- Figure 11 56
- Turn the oscilloscope off 57
- Turn the oscilloscope on 57
- (HP 54656A only) 60
- To document a single step 61
- Solutions 62
- Set the vertical sensitivity 67
- Set the vertical position 67
- Create the mask 67
- Rise time testing mask 69
- Determine the fail region 76
- Horizontal accuracy 78
- Figure 23 79
- Figure 24 81
- Test sequence example 82
- Documentation of step #1 83
- Documentation of step #2 83
- Figure 28 84
- Figure 29 84
- Figure 30 85
- Figure 31 85
- Figure 32 86
- Test Sequencing 88
- Programming 88
- Programming Conventions 90
- :SEQuence:NEXT 91
- :SEQuence:PREVious 92
- :SEQuence:PROTect 93
- :SEQuence:RESet 94
- :SEQuence:SETup 95
- :SEQuence:STEP 97
- :SEQuence:TEST? 98
- Reference 100
- Information 100
- Introduction 101
- Operating Characteristics 102
- Mask Template Testing 103
- Hard copy Output 103
- Reference Information 103
- RS-232 pin out 105
- Figure 34 106
- Figure 35 106
- Figure 36 107
- Timing of the output lines 109
- HP 54653A 110
- ScopeLink 2.0 110
- Software 110
- To document a test sequence 116
Powiązane produkty i podręczniki dla Pomiary, testowanie i kontrola Agilent Technologies HP 54601B
Pomiary, testowanie i kontrola Agilent Technologies InfiniiVision 3000 3024A MSO-X Dokumentacja
(37 strony)
(37 strony)
Pomiary, testowanie i kontrola Agilent Technologies InfiniiVision 7000B Series Podręcznik Użytkownika
(428 strony)
(428 strony)
© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.048 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji