Agilent Technologies Ininiium 9000 Dokumentacja Strona 46
- Strona / 166
- Spis treści
- ROZWIĄZYWANIE PROBLEMÓW
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
Chapter 3: Calibration
To run the self calibration
46
Figure 3-1
Calibration Dialog
4
Click Start, then follow the instructions on the screen.
The routine will ask you to do the following things in sequence:
a Decide if you want to perform the Time Scale Calibration. Your choices are:
• Standard Calibration - Time scale calibration will not be performed. Time scale calibration
factors from the previous time scale calibration will be used and the 10 MHz reference signal
will not be required. The remaining calibration procedure will continue.
• Standard Calibration and Time Scale Calibration - Performs the time scale calibration. This
option requires you to connect a 10 MHz reference signal to channel 1 that meets the following
specifications. Failure to use a reference signal that meets this specification will result in an
inaccurate calibration.
• Standard Calibration and Reset Time Scale Calibration - Factory time scale calibration factors
will be used. The 10 MHz reference signal will not be required. The remaining calibration
procedure will continue.
b Disconnect everything from all inputs and Aux Out.
c Connect the 50 BNC cable from Aux Out to channel 1.
d Connect the 50 BNC cable from Aux Out to each of the channel inputs as requested.
e Follow the directions for calibrating the digital channels (MSO models only).
f A Passed/Failed indication is displayed for each calibration section. If any section fails, check
the calibration cables and run the oscilloscope Self Test in the Utilities menu. Page 87 also has
a little section on what to do if a self cal fails in terms of replacing assemblies.
5
After the calibration procedure is completed, click Close.
Click here to start
calibration
Clear this check
box before
starting
calibration
Frequency: 10 MHz ±0.4 ppm = 10 MHz ±4 Hz
Amplitude: 0.2 Vpeak-to-peak to 5.0 Vpeak-to-peak
Wave shape: Sine or Square
- Service Guide 1
- In This Book 3
- DC Gain Accuracy Test 59 5
- General Information 7
- Model Bandwidth 9
- DSO/MSO9104A 1 GHz bandwidth 9
- DSO/MSO9404A 4 GHz bandwidth 9
- Accessories supplied 10
- Environmental Conditions 11
- Measurement Category 11
- Oscilloscope Dimensions 12
- Setting Up the Oscilloscope 13
- To inspect package contents 15
- Technical Specifications 20
- 1 mV to < 10 mV/div: \2 V 21
- Figure 0-1 26
- To connect power 27
- Side Panel 29
- Probing the Circuit 31
- Figure 0-5 32
- To turn on the oscilloscope 33
- To turn off the oscilloscope 34
- To clean the oscilloscope 39
- Calibration 43
- To run the self calibration 45
- Testing Performance 47
- Performance Test Interval 48
- Performance Test Record 48
- Test Order 48
- Test Equipment 48
- • DC Gain Accuracy Test 50
- To test input impedance 51
- Offset Accuracy Test 52
- column (Offset 54
- Channel 1 57
- DC Gain Accuracy Test 59
- BNC (f) to dual banana 60
- (1251-2277) 60
- 6614C DC Supply 60
- Record the 62
- Click here and enter 16E-9 67
- Time Scale Accuracy (TSA) 72
- 9000A Oscilloscope 73
- E8257D Sine Wave Source 73
- Agilent Technologies 75
- Troubleshooting 83
- Default Setup 85
- Primary Trouble Isolation 87
- Self Calibration 90
- 4 of this service manual 90
- Assembly Level Repair 94
- Display Trouble Isolation 96
- Chapter 5: Troubleshooting 100
- Front Panel Trouble Isolation 102
- Motherboard Verification 103
- To setup the BIOS 104
- To check the LEDs 109
- Software Revisions 110
- To check probe power outputs 111
- Replacing Assemblies 113
- Remove these two screws 117
- Then remove this 136
- Perform self tests 140
- Performance calibration 140
- Replaceable Parts 145
- Exploded Views 147
- Chapter 7: Replaceable Parts 148
- Replaceable Parts List 151
- Theory of Operation 155
- XC 3 S 1 0 0 158
- Block-Level Theory 160
- Chapter : 162
Powiązane produkty i podręczniki dla Pomiary, testowanie i kontrola Agilent Technologies Ininiium 9000
Pomiary, testowanie i kontrola Agilent Technologies InfiniiVision 3000 3024A MSO-X Dokumentacja
(37 strony)
(37 strony)
Pomiary, testowanie i kontrola Agilent Technologies InfiniiVision 7000B Series Podręcznik Użytkownika
(428 strony)
(428 strony)
© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.026 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji