Agilent Technologies InfiniiVision 6000 Series Instrukcja Obsługi Strona 462
- Strona / 934
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
462 Agilent InfiniiVision 6000 Series Oscilloscopes Programmer's Guide
5 Commands by Subsystem
:SYSTem:PRECision
(see page 798)
Command Syntax
:SYSTem:PRECision <value>
<value> ::= {{1 | ON} | {0 | OFF}}
The :SYSTem:PRECision command turns the oscilloscope's precision
analysis setting on or off.
• OFF (0) — provides the maximum oscilloscope waveform update rate by
performing measurements and math functions on a 1000- point
measurement record.
• ON (1) — at the expense of oscilloscope waveform update rate, this
setting allows measurements and math functions to be performed on a
precision analysis record (see ":WAVeform:POINts:MODE" on page 643).
The precision analysis setting is OFF after a *RST command.
Precision analysis is not available when:
• Realtime sampling mode is off.
• Averaging or High Resolution acquisition modes are selected.
• XY or Roll time modes are selected.
Query Syntax
:SYSTem:PRECision?
The :SYSTem:PRECision? query returns the current precision analysis
setting.
Return Format
<value><NL>
<value> ::= {1 | 0}
See Also • "Introduction to :SYSTem Commands" on page 457
• ":WAVeform:POINts:MODE" on page 643
• "*RST (Reset)" on page 140
- Agilent InfiniiVision 1
- 6000 Series 1
- Oscilloscopes 1
- In This Book 3
- Contents 5
- 6 Commands A-Z 17
- 8 Error Messages 19
- 9 Status Reporting 19
- 10 Synchronizing Acquisitions 19
- 12 Programming Examples 20
- What's New 21
- 1 What's New 22
- Commands 31
- Obsolete 31
- Setting Up 47
- 2 Setting Up 48
- Using the LAN Interface 49
- Using the GPIB Interface 50
- Setting Up 2 51
- Address 53
- Click Test Connection 53
- Getting Started 57
- Initializing 58
- Capturing Data 58
- Analyzing Captured Data 59
- Programming the Oscilloscope 60
- 3 Getting Started 62
- Getting Started 3 63
- Ensure New Data is Collected 64
- Checking Instrument Status 68
- Telnet Sockets 69
- Commands Quick Reference 71
- Command Summary 72
- 4 Commands Quick Reference 100
- Syntax Elements 120
- Commands Quick Reference 4 121
- Commands by Subsystem 123
- 5 Commands by Subsystem 124
- Common (*) Commands 125
- *CLS (Clear Status) 129
- Commands by Subsystem 5 133
- *IDN (Identification Number) 134
- *LRN (Learn Device Setup) 135
- *OPC (Operation Complete) 136
- *OPT (Option Identification) 137
- *RCL (Recall) 139
- *RST (Reset) 140
- *SAV (Save) 143
- *SRE (Service Request Enable) 144
- <mask><NL> 145
- *STB (Read Status Byte) 146
- *TRG (Trigger) 148
- *TST (Self Test) 149
- *WAI (Wait To Continue) 150
- Root (:) Commands 151
- :ACTivity 154
- :AER (Arm Event Register) 155
- :AUToscale 156
- :AUToscale:AMODE 158
- :AUToscale:CHANnels 159
- :CDISplay 161
- :DIGitize 162
- :MTEenable <mask> 171
- :MTEenable? 171
- :MTERegister[:EVENt]? 173
- <value><NL> 173
- :OPEE <mask> 175
- (see page 798) 177
- Query Syntax 177
- :OVLRegister? 183
- Return Format: 187
- :TER (Trigger Event Register) 191
- :ACQuire Commands 193
- :ACQuire:AALias 195
- :ACQuire:COMPlete 196
- :ACQuire:COUNt 197
- :ACQuire:DAALias 198
- :ACQuire:MODE 199
- :ACQuire:POINts 200
- :ACQuire:RSIGnal 201
- :ACQuire:SEGMented:ANALyze 202
- :ACQuire:SEGMented:COUNt 203
- :ACQuire:SEGMented:INDex 204
- :ACQuire:SRATe 207
- :ACQuire:TYPE 208
- :BUS<n> Commands 210
- :BUS<n>:BIT<m> 212
- :BUS<n>:BITS 213
- :BUS<n>:CLEar 215
- :BUS<n>:DISPlay 216
- :BUS<n>:LABel 217
- :BUS<n>:MASK 218
- :CALibrate Commands 219
- :CALibrate:DATE 221
- :CALibrate:LABel 222
- :CALibrate:OUTPut 223
- :CALibrate:STARt 224
- :CALibrate:STATus 225
- :CALibrate:SWITch 226
- :CALibrate:TEMPerature 227
- :CALibrate:TIME 228
- :CHANnel<n> Commands 229
- :CHANnel<n>:BWLimit 232
- :CHANnel<n>:COUPling 233
- :CHANnel<n>:DISPlay 234
- :CHANnel<n>:IMPedance 235
- :CHANnel<n>:INVert 236
- :CHANnel<n>:LABel 237
- :CHANnel<n>:OFFSet 238
- :CHANnel<n>:PROBe 239
- :CHANnel<n>:PROBe:ID 241
- :CHANnel<n>:PROBe:SKEW 242
- :CHANnel<n>:PROBe:STYPe 243
- :CHANnel<n>:PROTection 244
- :CHANnel<n>:RANGe 245
- :CHANnel<n>:SCALe 246
- :CHANnel<n>:UNITs 247
- :CHANnel<n>:VERNier 248
- :DIGital<n> Commands 249
- :DIGital<n>:DISPlay 251
- :DIGital<n>:LABel 252
- :DIGital<n>:POSition 253
- :DIGital<n>:SIZE 254
- :DIGital<n>:THReshold 255
- :DISPlay Commands 256
- :DISPlay:CLEar 258
- :DISPlay:DATA 259
- :DISPlay:LABel 261
- :DISPlay:LABList 262
- :DISPlay:PERSistence 263
- :DISPlay:SOURce 264
- :DISPlay:VECTors 265
- :EXTernal Trigger Commands 266
- :EXTernal:BWLimit 268
- :EXTernal:IMPedance 269
- :EXTernal:PROBe 270
- :EXTernal:PROBe:ID 271
- :EXTernal:PROBe:STYPe 272
- :EXTernal:PROTection 273
- :EXTernal:RANGe 274
- :EXTernal:UNITs 275
- :FUNCtion Commands 276
- :FUNCtion:CENTer 279
- :FUNCtion:DISPlay 280
- :FUNCtion:GOFT:OPERation 281
- :FUNCtion:GOFT:SOURce1 282
- :FUNCtion:GOFT:SOURce2 283
- :FUNCtion:OFFSet 284
- :FUNCtion:OPERation 285
- :FUNCtion:RANGe 286
- :FUNCtion:REFerence 287
- :FUNCtion:SCALe 288
- :FUNCtion:SOURce1 289
- :FUNCtion:SOURce2 290
- :FUNCtion:SPAN 291
- :FUNCtion:WINDow 292
- :HARDcopy Commands 293
- :HARDcopy:AREA 295
- :HARDcopy:APRinter 296
- :HARDcopy:FACTors 297
- :HARDcopy:FFEed 298
- :HARDcopy:INKSaver 299
- :HARDcopy:LAYout 300
- :HARDcopy:PALette 301
- :HARDcopy:PRINter:LIST 302
- :HARDcopy:STARt 303
- :LISTer Commands 304
- :LISTer:DATA 305
- :LISTer:DISPlay 306
- :MARKer Commands 307
- :MARKer:MODE 309
- :MARKer:X1Position 310
- :MARKer:X1Y1source 311
- :MARKer:X2Position 312
- :MARKer:X2Y2source 313
- :MARKer:XDELta 314
- :MARKer:Y1Position 315
- :MARKer:Y2Position 316
- :MARKer:YDELta 317
- :MEASure Commands 318
- Return Format 325
- :MEASure:CLEar 326
- :MEASure:COUNter 327
- :MEASure:DEFine 328
- :MEASure:DELay 331
- :MEASure:DUTYcycle 333
- :MEASure:FALLtime 334
- :MEASure:FREQuency 335
- :MEASure:NWIDth 336
- :MEASure:OVERshoot 337
- :MEASure:PERiod 339
- :MEASure:PHASe 340
- :MEASure:PREShoot 341
- :MEASure:PWIDth 342
- :MEASure:RESults 343
- :MEASure:RISetime 346
- :MEASure:SDEViation 347
- :MEASure:SHOW 348
- :MEASure:SOURce 349
- :MEASure:STATistics 351
- :MEASure:STATistics:INCRement 352
- :MEASure:STATistics:RESet 353
- :MEASure:TEDGe 354
- :MEASure:TVALue 356
- :MEASure:VAMPlitude 358
- :MEASure:VAVerage 359
- :MEASure:VBASe 360
- :MEASure:VMAX 361
- :MEASure:VMIN 362
- :MEASure:VPP 363
- :MEASure:VRATio 364
- :MEASure:VRMS 365
- :MEASure:VTIMe 366
- :MEASure:VTOP 367
- :MEASure:XMAX 368
- :MEASure:XMIN 369
- :MTESt Commands 370
- :MTESt:AMASk:CREate 375
- :MTESt:AMASk:SOURce 376
- :MTESt:AMASk:UNITs 377
- :MTESt:AMASk:XDELta 378
- :MTESt:AMASk:YDELta 379
- :MTESt:COUNt:FWAVeforms 380
- :MTESt:COUNt:RESet 381
- :MTESt:COUNt:TIME 382
- :MTESt:COUNt:WAVeforms 383
- :MTESt:DATA 384
- :MTESt:DELete 385
- :MTESt:ENABle 386
- :MTESt:LOCK 387
- :MTESt:OUTPut 388
- :MTESt:RMODe 389
- :MTESt:RMODe:FACTion:MEASure 390
- :MTESt:RMODe:FACTion:PRINt 391
- :MTESt:RMODe:FACTion:SAVE 392
- :MTESt:RMODe:FACTion:STOP 393
- :MTESt:RMODe:SIGMa 394
- :MTESt:RMODe:TIME 395
- :MTESt:RMODe:WAVeforms 396
- :MTESt:SCALe:BIND 397
- :MTESt:SCALe:X1 398
- :MTESt:SCALe:XDELta 399
- :MTESt:SCALe:Y1 400
- :MTESt:SCALe:Y2 401
- :MTESt:SOURce 402
- :MTESt:TITLe 403
- :POD Commands 404
- :POD<n>:DISPlay 405
- :POD<n>:SIZE 406
- :POD<n>:THReshold 407
- :RECall Commands 409
- :RECall:FILename 410
- :RECall:IMAGe[:STARt] 411
- :RECall:MASK[:STARt] 412
- :RECall:PWD 413
- :RECall:SETup[:STARt] 414
- :SAVE Commands 415
- :SAVE:FILename 417
- :SAVE:IMAGe[:STARt] 418
- :SAVE:IMAGe:AREA 419
- :SAVE:IMAGe:FACTors 420
- :SAVE:IMAGe:FORMat 421
- :SAVE:IMAGe:INKSaver 422
- :SAVE:IMAGe:PALette 423
- :SAVE:LISTer[:STARt] 424
- :SAVE:MASK[:STARt] 425
- :SAVE:PWD 426
- :SAVE:SETup[:STARt] 427
- :SAVE:WAVeform[:STARt] 428
- :SAVE:WAVeform:FORMat 429
- :SAVE:WAVeform:LENGth 430
- :SAVE:WAVeform:SEGMented 431
- :SBUS Commands 432
- :SBUS:DISP 0;MODE IIC 433
- :SBUS:CAN:COUNt:ERRor 434
- :SBUS:CAN:COUNt:OVERload 435
- :SBUS:CAN:COUNt:RESet 436
- :SBUS:CAN:COUNt:TOTal 437
- :SBUS:CAN:COUNt:UTILization 438
- :SBUS:DISPlay 439
- :SBUS:FLEXray:COUNt:NULL 440
- :SBUS:FLEXray:COUNt:RESet 441
- :SBUS:FLEXray:COUNt:SYNC 442
- :SBUS:FLEXray:COUNt:TOTal 443
- :SBUS:I2S:BASE 444
- :SBUS:IIC:ASIZe 445
- :SBUS:LIN:PARity 446
- :SBUS:M1553:BASE 447
- :SBUS:MODE 448
- :SBUS:SPI:BITorder 449
- :SBUS:SPI:WIDTh 450
- :SBUS:UART:BASE 451
- :SBUS:UART:COUNt:ERRor 452
- :SBUS:UART:COUNt:RESet 453
- :SBUS:UART:COUNt:RXFRames 454
- :SBUS:UART:COUNt:TXFRames 455
- :SBUS:UART:FRAMing 456
- :SYSTem Commands 457
- :SYSTem:DATE 458
- :SYSTem:DSP 459
- :SYSTem:ERRor 460
- :SYSTem:LOCK 461
- :SYSTem:PRECision 462
- :SYSTem:PROTection:LOCK 463
- :SYSTem:SETup 464
- :SYSTem:TIME 466
- :TIMebase Commands 467
- :TIMebase:MODE 469
- :TIMebase:POSition 470
- :TIMebase:RANGe 471
- :TIMebase:REFClock 472
- :TIMebase:REFerence 473
- :TIMebase:SCALe 474
- :TIMebase:VERNier 475
- :TIMebase:WINDow:POSition 476
- :TIMebase:WINDow:RANGe 477
- :TIMebase:WINDow:SCALe 478
- :TRIGger Commands 479
- General :TRIGger Commands 482
- :TRIGger:HFReject 483
- :TRIGger:HOLDoff 484
- :TRIGger:MODE 485
- :TRIGger:NREJect 486
- :TRIGger:PATTern 487
- :TRIGger:SWEep 489
- :TRIGger:CAN Commands 490
- :TRIGger:CAN:PATTern:DATA 492
- :TRIGger:CAN:PATTern:ID 494
- :TRIGger:CAN:PATTern:ID:MODE 495
- :TRIGger:CAN:SAMPlepoint 496
- :TRIGger:CAN:SIGNal:BAUDrate 497
- :TRIGger:CAN:SOURce 498
- :TRIGger:CAN:TRIGger 499
- :TRIGger:DURation Commands 501
- :TRIGger:DURation:GREaterthan 502
- :TRIGger:DURation:LESSthan 503
- :TRIGger:DURation:PATTern 504
- :TRIGger:DURation:QUALifier 505
- :TRIGger:DURation:RANGe 506
- :TRIGger:EBURst Commands 507
- :TRIGger:EBURst:COUNt 508
- :TRIGger:EBURst:IDLE 509
- :TRIGger:EBURst:SLOPe 510
- :TRIGger[:EDGE] Commands 511
- :TRIGger[:EDGE]:COUPling 512
- :TRIGger[:EDGE]:LEVel 513
- :TRIGger[:EDGE]:REJect 514
- :TRIGger[:EDGE]:SLOPe 515
- :TRIGger[:EDGE]:SOURce 516
- :TRIGger:FLEXray Commands 517
- :TRIGger:FLEXray:AUTosetup 518
- :TRIGger:FLEXray:BAUDrate 519
- :TRIGger:FLEXray:CHANnel 520
- :TRIGger:FLEXray:ERRor:TYPE 521
- :TRIGger:FLEXray:EVENt:TYPE 522
- :TRIGger:FLEXray:FRAMe:CCBase 523
- :TRIGger:FLEXray:FRAMe:ID 525
- :TRIGger:FLEXray:FRAMe:TYPE 526
- :TRIGger:FLEXray:SOURce 527
- :TRIGger:FLEXray:TRIGger 528
- :TRIGger:GLITch Commands 529
- :TRIGger:GLITch:GREaterthan 531
- :TRIGger:GLITch:LESSthan 532
- :TRIGger:GLITch:LEVel 533
- :TRIGger:GLITch:POLarity 534
- :TRIGger:GLITch:QUALifier 535
- :TRIGger:GLITch:RANGe 536
- :TRIGger:GLITch:SOURce 537
- :TRIGger:I2S Commands 538
- :TRIGger:I2S:ALIGnment 540
- :TRIGger:I2S:AUDio 541
- :TRIGger:I2S:CLOCk:SLOPe 542
- :TRIGger:I2S:PATTern:DATA 543
- :TRIGger:I2S:PATTern:FORMat 545
- :TRIGger:I2S:RANGe 546
- :TRIGger:I2S:RWIDth 548
- :TRIGger:I2S:SOURce:CLOCk 549
- :TRIGger:I2S:SOURce:DATA 550
- :TRIGger:I2S:SOURce:WSELect 551
- :TRIGger:I2S:TRIGger 552
- :TRIGger:I2S:TWIDth 554
- :TRIGger:I2S:WSLow 555
- :TRIGger:IIC Commands 556
- :TRIGger:IIC:PATTern:ADDRess 557
- :TRIGger:IIC:PATTern:DATA 558
- :TRIGger:IIC:PATTern:DATa2 559
- :TRIGger:IIC[:SOURce]:CLOCk 560
- :TRIGger:IIC[:SOURce]:DATA 561
- :TRIGger:IIC:TRIGger[:TYPE] 563
- :TRIGger:LIN Commands 565
- :TRIGger:LIN:ID 567
- :TRIGger:LIN:PATTern:DATA 568
- :TRIGger:LIN:PATTern:FORMat 571
- :TRIGger:LIN:SAMPlepoint 572
- :TRIGger:LIN:SIGNal:BAUDrate 573
- :TRIGger:LIN:SOURce 574
- :TRIGger:LIN:STANdard 575
- :TRIGger:LIN:SYNCbreak 576
- :TRIGger:LIN:TRIGger 577
- :TRIGger:M1553 Commands 578
- :TRIGger:M1553:AUTosetup 579
- :TRIGger:M1553:PATTern:DATA 580
- :TRIGger:M1553:RTA 581
- :TRIGger:M1553:SOURce:LOWer 582
- :TRIGger:M1553:SOURce:UPPer 583
- :TRIGger:M1553:TYPE 584
- :TRIGger:SEQuence Commands 585
- :TRIGger:SEQuence:COUNt 586
- :TRIGger:SEQuence:EDGE 587
- :TRIGger:SEQuence:FIND 588
- :TRIGger:SEQuence:PATTern 589
- :TRIGger:SEQuence:RESet 590
- :TRIGger:SEQuence:TIMer 591
- :TRIGger:SEQuence:TRIGger 592
- :TRIGger:SPI Commands 593
- :TRIGger:SPI:CLOCk:SLOPe 594
- :TRIGger:SPI:CLOCk:TIMeout 595
- :TRIGger:SPI:FRAMing 596
- :TRIGger:SPI:PATTern:DATA 597
- :TRIGger:SPI:PATTern:WIDTh 598
- :TRIGger:SPI:SOURce:CLOCk 599
- :TRIGger:SPI:SOURce:DATA 600
- :TRIGger:SPI:SOURce:FRAMe 601
- :TRIGger:TV Commands 602
- :TRIGger:TV:LINE 603
- :TRIGger:TV:MODE 604
- :TRIGger:TV:POLarity 605
- :TRIGger:TV:SOURce 606
- :TRIGger:TV:STANdard 607
- :TRIGger:UART Commands 608
- :TRIGger:UART:BASE 610
- :TRIGger:UART:BAUDrate 611
- :TRIGger:UART:BITorder 612
- :TRIGger:UART:BURSt 613
- :TRIGger:UART:DATA 614
- :TRIGger:UART:IDLE 615
- :TRIGger:UART:PARity 616
- :TRIGger:UART:POLarity 617
- :TRIGger:UART:QUALifier 618
- :TRIGger:UART:SOURce:RX 619
- :TRIGger:UART:SOURce:TX 620
- :TRIGger:UART:TYPE 621
- :TRIGger:UART:WIDTh 622
- :TRIGger:USB Commands 623
- :TRIGger:USB:SOURce:DMINus 624
- :TRIGger:USB:SOURce:DPLus 625
- :TRIGger:USB:SPEed 626
- :TRIGger:USB:TRIGger 627
- :WAVeform Commands 628
- POD1 D7 D6 D5 D4 D3 D2 D1 D0 635
- :WAVeform:BYTeorder 636
- :WAVeform:COUNt 637
- :WAVeform:DATA 638
- :WAVeform:FORMat 640
- :WAVeform:POINts 641
- :WAVeform:POINts:MODE 643
- :WAVeform:PREamble 645
- :WAVeform:SEGMented:COUNt 648
- :WAVeform:SEGMented:TTAG 649
- :WAVeform:SOURce 650
- :WAVeform:SOURce:SUBSource 654
- :WAVeform:TYPE 655
- :WAVeform:UNSigned 656
- :WAVeform:VIEW 657
- :WAVeform:XINCrement 658
- :WAVeform:XORigin 659
- :WAVeform:XREFerence 660
- :WAVeform:YINCrement 661
- :WAVeform:YORigin 662
- :WAVeform:YREFerence 663
- Commands A-Z 665
- Commands A-Z 6 667
- Commands" on page 798) 699
- Discontinued 704
- Parameters 704
- :CHANnel:ACTivity 705
- :CHANnel:LABel 706
- :CHANnel:THReshold 707
- :CHANnel2:SKEW 708
- :CHANnel<n>:INPut 709
- :CHANnel<n>:PMODe 710
- :DISPlay:CONNect 711
- :DISPlay:ORDer 712
- Command Syntax 713
- :EXTernal:INPut 714
- :EXTernal:PMODe 715
- :FUNCtion:SOURce 716
- :FUNCtion:VIEW 717
- :HARDcopy:DESTination 718
- :HARDcopy:DEVice 719
- :HARDcopy:FILename 720
- :HARDcopy:FORMat 721
- :HARDcopy:GRAYscale 722
- :HARDcopy:IGColors 723
- :HARDcopy:PDRiver 724
- :MEASure:LOWer 725
- :MEASure:SCRatch 726
- :MEASure:TDELta 727
- :MEASure:THResholds 728
- :MEASure:TMAX 729
- :MEASure:TMIN 730
- :MEASure:TSTArt 731
- :MEASure:TSTOp 732
- :MEASure:TVOLt 733
- :MEASure:UPPer 735
- :MEASure:VDELta 736
- :MEASure:VSTArt 737
- :MEASure:VSTOp 738
- :MTESt:AMASk:{SAVE 739
- :MTESt:AVERage 740
- :MTESt:AVERage:COUNt 741
- :MTESt:LOAD 742
- :MTESt:RUMode 743
- :MTESt:RUMode:SOFailure 744
- :MTESt:{STARt 745
- :MTESt:TRIGger:SOURce 746
- DISK invalid 748
- PCL invalid 748
- Old Print Option: Is Now: 748
- :TIMebase:DELay 749
- :TRIGger:CAN:ACKNowledge 750
- <value> ::= DIFF 751
- <value> ::= LIN 752
- :TRIGger:THReshold 753
- :TRIGger:TV:TVMode 754
- Error Messages 755
- Error Messages 8 757
- Status Reporting 763
- Status Reporting 9 765
- Status Byte Register (STB) 769
- Trigger Event Register (TER) 772
- Output Queue 773
- Message Queue 774
- Error Queue 777
- Status Condition Register 779
- Arm Event Register (AER) 780
- Clearing Registers and Queues 785
- Synchronizing Acquisitions 787
- Set Up the Oscilloscope 788
- Acquire a Waveform 788
- Retrieve Results 788
- Blocking Synchronization 789
- Synchronizing Acquisitions 10 791
- Command Classifications 798 797
- Query Return Values 820 797
- Command Classifications 798
- ":DISPLAY:LABEL ON" 799
- Program Message 799
- Instruction Header 799
- Separator 799
- Program Data 799
- Simple Command Headers 801
- Compound Command Headers 801
- Common Command Headers 802
- Program Data Syntax Rules 802
- Command Tree 803
- Duplicate Mnemonics 817
- Query Return Values 820
- Programming Examples 823
- VISA COM Examples 824
- Programming Examples 12 825
- " + _ 831
- VISA COM Example in C# 834
- VISA Examples 857
- VISA Example in Visual Basic 866
- VISA Example in C# 876
- SICL Examples 903
- SICL Example in Visual Basic 912
- Numerics 921
- , 284, 287 926
Powiązane produkty i podręczniki dla Multimetry Agilent Technologies InfiniiVision 6000 Series
(349 strony)
(193 strony)© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.076 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji