Agilent Technologies 54657A Dokumentacja Strona 173
- Strona / 188
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
Glossary
This glossary is organized into
two parts: oscilloscope and
TV/video trigger terms. The
TV/video trigger terms apply to
oscilloscopes with Option 005
installed.
Oscilloscope Terms
50Ω Input Protection
This only
functions when the scope is powered
on. The 50Ω load will typically dis-
connect if greater than 5 Vrms is
detected. However, the inputs could
still be damaged, depending on the
time constant of the signal.
Auto A trigger mode that pro-
duces a baseline display if the trigger
conditions are not met. If the trigger
frequency is less than 25 Hz, a free
running display will result even if the
level and slope conditions are met.
Auto Level The oscilloscope sets
the trigger point to the 50% ampli-
tude point on the displayed
waveform. If there is no signal pre-
sent, a baseline is displayed.
Autoscale Front-panel key that
automatically sets up the oscillo-
scope to display a signal.
Autostore displays the stored
waveforms in half bright, and the
most recent trace is displayed in full
bright.
Baseline Free running trace on
the display when no signal is applied
and the trigger mode is set to auto or
auto level.
BW Lim (Bandwidth Limit) Limits
the displayed bandwidth of the se-
lected channel to 30 MHz, and is
available for channels 1 and 2 only.
This feature is useful for viewing
noisy signals
Couplng (Coupling) This changes
the input coupling. Channels 1 and
2 allow dc, ac, or ground. External
Trigger allow dc or ac.
Cursors Horizontal and vertical
markers used for making custom volt-
age and time measurements.
Delay In main sweep, the delay
knob moves the sweep horizontally,
and indicates how far the time refer-
ence is from the trigger point. In
delayed sweep the delay knob moves
the starting point of the portion of
the main sweep to be expanded by
the delayed sweep.
Glossary–1
- Agilent 54615B, 54616B 1
- Oscilloscopes 1
- Accessories supplied 3
- Accessories available 3
- Options available 4
- Contents 7
- 4Service 8
- 5 Performance Characteristics 9
- Glossary 10
- The Oscilloscope at a Glance 11
- Figure 1–1 13
- Figure 1–2 13
- Figure 1–3 14
- Press Autoscale 17
- To set up the vertical window 18
- To expand the vertical signal 20
- To set up the time base 21
- ▼ happened before the 22
- To trigger the oscilloscope 23
- Mode 24
- Slope/Coupling 25
- To use roll mode 26
- Using Color (54616C only) 27
- To print in color 30
- Operating Your Oscilloscope 31
- To use delayed sweep 33
- Time reference set to left 34
- Delayed sweep 34
- Time reference set to center 35
- Press Autostore 36
- Erase 37
- Autostore 37
- To capture a single event 38
- Find the glitch 40
- Press Time 44
- Press the Freq softkey 44
- Press the Next Menu softkey 47
- Press the Rise Time softkey 48
- Press Voltage 50
- Press the Vrms softkey 51
- To make cursor measurements 53
- Figure 2-11 54
- Figure 2-12 54
- Figure 2-13 55
- Figure 2-14 55
- Figure 2-15 56
- Figure 2-16 56
- To save or recall traces 63
- Press Setup 64
- To reset the instrument setup 65
- To use the XY display mode 66
- Press Cursors 67
- Figure 2-26 69
- Figure 2-27 69
- To analyze video waveforms 70
- Using Option 005 Enhanced 73
- TV/Video Trigger 73
- To select TV display grid 76
- Cursors key 77
- Triggering on All Lines 79
- Triggering on Field 1 80
- Serration pulses 80
- Equalizing pulses 80
- Figure 3-7 85
- Figure 3-8 87
- Figure 3-9 87
- CALIBRATOR 98
- Set up the oscilloscope 100
- To verify bandwidth 102
- To verify trigger sensitivity 107
- 100 MHz, 75 mV p-p 109
- Adjusting the Oscilloscope 113
- To adjust the power supply 114
- (top side of oscilloscope) 116
- +5.1 V adjust 116
- –5.25 V adjust 116
- CALIBRATOR output 118
- ∆V(2) for ∆V(1) 120
- Model/Part 121
- 19, and 20 125
- Is the fan running? 128
- To clear error messages 129
- Perform the keyboard test 134
- Perform the ROM test 135
- Perform the RAM test 135
- To troubleshoot Option 005 136
- To replace an assembly 138
- To remove the fan 139
- To remove the front panel 139
- To remove the display 141
- To remove the system board 141
- To remove the attenuator 142
- To remove the power supply 146
- To remove the keyboard 147
- To remove the handle 148
- To order a replacement part 149
- Figure 4-12 151
- Figure 4–13 152
- Reference 153
- Designator 153
- Agilent Part 153
- Qty Description 153
- Figure 4-14 156
- Performance Characteristics 159
- Horizontal System 162
- Trigger System 163
- TV Functions 164
- XY Operation 164
- Display System 164
- Acquisition System 165
- Advanced Functions 166
- Power Requirements 166
- (54615B and 54616B only) 167
- General (54616C only) 169
- (54615B, 54616B, and 54616C) 170
- Option 005 Trigger System 172
- Oscilloscope Terms 173
- TV/Video Trigger Terms 177
- Glossary–8 180
- DECLARATION OF CONFORMITY 185
© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.040 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji