Agilent Technologies 86100B Instrukcja Użytkownika Pobierz pdf (Strona 15)

High Bandwidth, Single-Mode

Optical/Electrical Modules 86106B 86109A 86109B 86116A

86116B

OPTICAL CHANNEL SPECIFICATIONS

Optical Channel Unfiltered Bandwidth 28 GHz 30 GHz 40 GHz

53 GHz 65 GHz (best pulse fidelity)

Wavelength Range 1000–1600 nm 55 GHz (best sensitivity)

Calibrated Wavelengths 1310/1550 nm 1480-1620 nm

Optical Sensitivity

–7 dBm N/A

Transition Time (10% to 90%,

calculated from TR = 0.48/BW optical) 18 ps 16 ps 12 ps (FWHM)

9.0 ps (FWHM)

7.4 ps (FWHM)

RMS Noise

Characteristic 13 µW (Filtered) 12 µW 25 µW (30 GHz) 60 µW (50 GHz) 140 µW (65 GHz)

23 µW (Unfiltered) 65 µW (40 GHz) 190 µW (53 GHz) 50 µW (55 GHz)

Maximum 15 µW (Filtered) 30 µW 30 µW (30 GHz) 90 µW (50 GHz) 250 µW (65 GHz)

30 µW (Unfiltered) 75 µW (40 GHz) 260 c(53 GHz) 85 µW (55 GHz)

Scale Factor

Minimum 20 µW/division 200 µW/division

Maximum 500 µW/division 1.0 mW/division 2.5 mW/division 5 mW/division

CW Accuracy (single marker, ±50 µW ±4% of

referenced to average power monitor) (reading-channel offset) ±150 µW ±4% of (reading-channel offset)

CW Offset Range (referenced two

divisions from screen bottom) +1 mW to –3 mW +6 mW to –2 mW +5 mW to –15mW +8 to –12 mW

Average Power Monitor

(specified operating range) –27 dBm to +3 dBm –23 dBm to + 9 dBm

Factory Calibrated Accuracy ±5% ±100 nW ±connector uncertainty, 20°C to 30°C

User Calibrated Accuracy ±2% ±100 nW ±power meter uncertainty, <5°C change

Maximum Input Power

Maximum non-destruct average 2 mW (+3 dBm) 10 mW (+10 dBm)

Maximum non-destruct peak 10 mW (+10 dBm) 50 mW (+17 dBm)

Fiber Input 9/125 µm, user selectable connector

Input Return Loss

(HMS-10 connector fully filled fiber) 30 dB 20 dB

86116A requires the 86100A/B software revision A.3.0 or above.

Specified with 8 point moving average in frequency response.

FWHM (Full Width Half Max) as measured from optical pulse with 700 fs FWHM, 5 MHz repetition rate and 10 mW peak power.

Smallest average optical power required for mask test. Valves represent typical sensitivity of NRZ eye diagrams. Assumes mask test with compliance filter switched in.

ELECTRICAL CHANNEL SPECIFICATIONS

Electrical Channel Bandwidth 18 and 40 GHz 26 and 50 GHz 43 and 63 GHz 80, 55 and 30 GHz

Transition Time (10% to 90%, 19.5 ps (18 GHz) <13.2 ps (26 GHz) 8.1 ps (43 GHz) 6.4 ps (55 GHz)

calculated from TR = 0.35/BW) 9 ps (40 GHz) 7 ps (50 GHz) 5.6 ps (63 GHz) 4.4 ps (80 GHz)

RMS Noise

Characteristic 0.25 mV (18 GHz) 0.25 mV (26 GHz) 0.6 mV (43 GHz) 0.6 mV (55 GHz)

0.5 mV (40 GHz) 0.60 mV (50 GHz) 1.7 mV (63 GHz) 1.1 mV (80 GHz)

Maximum 0.5m V (18 GHz) 0.50 mV (26 GHz) 0.9 mV (43 GHz) 1.1 mV (55 GHz)

1.0 mV (40 GHz) 1.0 mV (50 GHz) 2.5 mV (63 GHz) 2.2 mV (80 GHz)

Scale Factor

Minimum 1 mV/division 2 mV/division

Maximum 100 mV/division 100 mV/division

DC Accuracy (single marker) ±0.4% of full scale ±0.4% of full scale ±0.8% of full scale ±0.4% of full scale

±2 mV ±1.5% of (reading- ±2 mV ±1.5% of (reading- ±2 mV ±1.5% of (reading- ±3 mV ±2% of (reading-

channel offset), 18 GHz channel offset), 26 GHz channel offset), 43 GHz channel offset), ±2% of

±0.4% of full scale ±0.4% of full scale ±2.5% of full scale offset (all bandwidths)

±2 mV ±3% of (reading- ±2 mV ±2% of (reading- ±2 mV ±2% of (reading-

channel offset), 40 GHz channel offset), 50 GHz channel offset), 63 GHz

DC Offset Range (referenced

to center of screen) ±500 mV

Input Dynamic Range

(relative to channel offset) ±400 mV

Maximum Input Signal ±2 V (+16 dBm)

Nominal Impedance 50 ohm

Reflections (for 20 ps rise time) 5% 10% (DC–70 GHz)

20% (70–100 GHz)

Electrical Input 2.4 mm (male) 1.85 mm (male)

Module Specifications: Single-Mode Optical/Electrical

1 2 ... 10 11 12 13 14 15 16 17 18 19 20 21 22

Komentarze do niniejszej Instrukcji

Brak uwag

Agilent Technologies 86100B Instrukcja Użytkownika Strona 15

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Pomiary, testowanie i kontrola Agilent Technologies 86100B