Agilent Technologies Agilent B2201A Instrukcja Użytkownika Strona 24
- Strona / 234
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
1-8 Agilent B2200 User’s Guide, Edition 2
Introduction
Switch Modules
Switch Modules
The Agilent B2200A and B2201A support the dedicated switch module, Agilent
B2210A and B2211A, respectively.
By installing the modules, the module inputs will be connected internally to the
front panel input connectors. And 12 output connectors will face the rear panel. The
type of the output connectors is the triaxial BNC. Up to six kelvin outputs are
available.
Image of the output terminals and the block diagram of the switch module are
shown in Figure 1-3 and Figure 1-4.
Figure 1-3 Switch Module Output Terminals
WARNING Do not touch the force and guard terminals of the output connectors while the
Agilent B2200 is turned on. Dangerous voltages up to the maximum input
voltage may be present at the output connectors.
NOTE Mixed configuration of the switch modules is not supported.
- Agilent B2200A 1
- Agilent B2201A 1
- Manual Part Number 2
- Warranty 2
- Technol o gy Licenses 2
- Restricted Rights Legend 2
- Safety Summary 5
- Safety Symbols 7
- In This Manual 8
- Contents 10
- 1 Introduction 17
- Agilent B2200 Series 19
- Front Panel 20
- Introduction 21
- Figure 1-1 Front Panel View 21
- Rear Panel 22
- Figure 1-2 Rear Panel View 23
- Switch Modules 24
- Specifications 26
- General Specifications 27
- Accessories and Options 31
- 2 Installation 35
- Requirements 37
- Installation 38
- Table 2-1 Power Cable 38
- Operating Environment 39
- Inspection 40
- Installing the B2200 41
- To Set the GPIB Address 42
- To Connect the GPIB Cable 42
- To Install the Switch Module 43
- To Install the Blank Panel 43
- Self-Test 44
- Output Connections 45
- Connector Plates 46
- To Install Interlock Circuit 49
- To Install LED Circuit 50
- Cathode(-) 51
- Anode(+) 51
- To Mount Connectors 52
- 2 − ∅11.3 ∅3.2 2 − M3 x 0.5 53
- 14 11 11 14 53
- Input Connections 54
- Measurement Cable Length 57
- Maintenance 59
- 3 Front Panel Operation 61
- Operation 63
- To Initialize Agilent B2200 64
- To Enable Light Pen 64
- To Change Connection Rule 65
- To Change Connection Sequence 65
- To Control Switch Condition 65
- To save the setup 66
- To load the setup 66
- To Use Bias Mode 67
- To Use Ground Mode 68
- To Use Couple Mode 69
- To Display Firmware Revision 69
- To Display Module Information 69
- To clear error buffer 70
- LED matrix 71
- Switch Control Functions 72
- Channel Configuration Mode 73
- Connection Rule 74
- Connection Sequence 75
- Bias Mode 76
- Ground Mode 78
- Couple Mode 80
- Display Functions 82
- SequenceRule 83
- GndLock Error GndBias 83
- Card Selection key 84
- Function Edit 85
- Function key group 86
- Break_Before_Make 87
- Settings: 01 [ ] 87
- SET VIEW 88
- ENABLE DISABLE 88
- Channel: 01 88
- Channel: No Channel 88
- Channel 01: ENABLED 88
- Setup Menus 90
- Selftest Menu 94
- Enter key 95
- Exit key to return to the 95
- 4 Programming 99
- :ROUT:CONN:RULE ALL,FREE 101
- :ROUT:CONN:SEQ ALL,BBM 101
- Fundamental Commands 102
- Switch Control 103
- Programming Examples 105
- Connecting Input-Output Paths 106
- Using Bias Mode 108
- Using Ground Mode 110
- Using Couple Mode 112
- Saving Input/Output Labels 114
- Capacitance Compensation 118
- Required Conditions 119
- FORCE or SENSE (A) 124
- FORCE or SENSE (B) 124
- Insulator 124
- Triaxial Cable 124
- 5 SCPI Command Reference 127
- Common Commands 130
- Subsystem Commands 139
- SCPI Command Reference 140
- Command Summary 140
- Relay Control Commands 140
- Command Description 140
- Bias Mode Commands 141
- Ground Mode Commands 142
- Couple Mode Commands 143
- :DIAGnostic:TEST:CARD:CLEar 147
- :DIAGnostic:TEST:CARD:STATe? 148
- :DIAGnostic:TEST:FRAMe:CLEar 148
- ENTER @Agb2200;A$ 151
- [:ROUTe]:AGND:PORT 153
- [:ROUTe]:AGND[:STATe] 154
- [:ROUTe]:AGND:UNUSED 155
- [:ROUTe]:BIAS:PORT 158
- [:ROUTe]:BIAS[:STATe] 159
- [:ROUTe]:CLOSe:CARD? 160
- [:ROUTe]:CLOSe[:LIST] 160
- [:ROUTe]:CONNection:RULE 161
- [:ROUTe]:CONNection:SEQuence 162
- [:ROUTe]:COUPle:PORT 163
- [:ROUTe]:COUPle:PORT:DETect 164
- [:ROUTe]:COUPle[:STATe] 165
- [:ROUTe]:FUNCtion 166
- [:ROUTe]:OPEN:CARD 166
- [:ROUTe]:OPEN[:LIST] 167
- [:ROUTe]:SYMBol:CHANnel 168
- [:ROUTe]:SYMBol:PORT 169
- :SYSTem:BEEP 170
- :SYSTem:CCONfig? 170
- :SYSTem:CDEScription? 171
- :SYSTem:CPON 172
- :SYSTem:CTYPe? 173
- :SYSTem:DISPlay:LCD 173
- :SYSTem:DISPlay:LED 174
- :SYSTem:DISPlay:STRing 174
- :SYSTem:ERRor? 175
- :SYSTem:KLC 175
- :SYSTem:MEMOry:COMMent 176
- :SYSTem:MEMOry:DELete 176
- :SYSTem:MEMOry:LOAD 177
- :SYSTem:MEMOry:SAVE 177
- :SYSTem:PEN 178
- :SYSTem:VERSion? 178
- Status Reporting Structure 179
- Status Byte Register 181
- Output Queue 186
- 6 VXI plug&play Driver 187
- System Requirements 189
- Driver Functions 191
- VXI plug&play Driver 220
- 7 Error Messages 221
- Standard SCPI Error Messages 223
- Execution Error 227
- Device-Dependent Errors 228
- Query Errors 229
- B2200 Channel Related Errors 231
Powiązane produkty i podręczniki dla Multimetry Agilent Technologies Agilent B2201A
(8 strony)© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.060 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji