Agilent Technologies 81134A Instrukcja Obsługi Pobierz pdf (Strona 23)

DIAGnostic Commands SCPI Commands Reference

Agilent 81133A/81134A Pulse Generator Programming Guide, March 2007 23

DIAGnostic Commands

The following table shows the Agilent 81133A/81134A Pulse

Generator DIAGnostic Commands.

Commands in the User Interface The following figure shows how the DIAGnostic commands are

implemented in the 81133A/81134A user interface.

Command Parameter Description

:CAL:TIM

Calibrates the timing system of

the instrument

:DIAG

:CHANnel[1|2]

:PPERformance[?] NORMal | FAST

| SMOoth

Sets/reads channel peak

performance

:CAL:TIM

:DIAG:CHANnel[1|2]

:PPERformance[?]

:TEST?

1 2 ... 18 19 20 21 22 23 24 25 26 27 28 ... 103 104

Programming Guide 1
Important Notice 2
About This Programming Guide 3
Contents 5
OUTPut Commands 39 6
SOURce Commands 45 6
Status Handling Commands 67 6
Troubleshooting 97 7
Introduction 10
SCPI Commands Reference 17
Common Commands 19
Standard Settings 21
DIAGnostic Commands 23
:CAL:TIM 24
DIGital Commands 25
Range Maximum Pattern Length 29
60 – 3360 Mhz 12 Mbit 29
30 – 60 Mhz 6 Mbit 29
15 – 30 Mhz 3 Mbit 29
CROSsover:[VALue] 32
CROSsover:[STATe] 34
DISPlay Commands 35
MEASure Commands 36
:MEASure:FREQuency? 37
:MEASure:PERiod? 38
OUTPut Commands 39
:OUTPut[0 41
:OUTPut0:SOURce 42
:OUTPut[0 43
:OUTPut[1 43
:OUTPut[1 44
:OUTPut:CENTral 44
SOURce Commands 45
[:SOURce]:FUNCtion[:SHAPe] 50
[:SOURce]:FUNCtion:MODe[1 51
[:SOURce]:PHASe[:ADJ][1 53
[:SOURce][:PULSe]:DCYCle[1 54
[:SOURce][:PULSe]:DELay[1 55
[:SOURce][:PULSe]:DESKew[1 56
[:SOURce][:PULSe]:DHOLd[1 56
[:SOURce][:PULSe]:PERiod 57
[:SOURce][:PULSe]:WIDTh[1 58
[:SOURce]:PM[1 59
[:SOURce]:PM[1 59
[:IMMediate][:AMPLitude] 60
[:IMMediate]:OFFSet 61
[:IMMediate]:HIGH 62
[:IMMediate]:LOW 63
[:IMMediate]:TERM 64
[:SOURce]:VOLTage[1 64
[:AMPLitude]? 64
Status Handling Commands 67
:STATus:OPERation 70
:STATus:PRESet 70
:STATus:QUEStionable 71
:STATus:QUEStionable:VOLTage 73
:STATus:QUEStionable:MONotony 76
SYSTem Commands 79
:SYSTem:ERRor? 81
:SYSTem:PRESet 81
:SYSTem:SET 82
:SYSTem:VERSion? 82
:ADDRess 84
:DGATeway 85
TRIGger Commands 86
:TRIGger:SOURce 87
:TRIGger:TERM 88
:TRIGger:TERM:STATE[?] 89
ARM Commands 90
:ARM[:SEQuence][:LAYer]:LEVel 91
:ARM[:SEQuence][:LAYer]:SLOPe 92
:ARM[:SEQuence][:LAYer]:TERM 94
:ARM[:SEQuence][:LAYer]:STOP 95
Troubleshooting 100
5988-7402EN 104

Komentarze do niniejszej Instrukcji

Brak uwag

Agilent Technologies 81134A Instrukcja Obsługi Strona 23

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Pomiary, testowanie i kontrola Agilent Technologies 81134A