Agilent Technologies AGILENT U2761A Instrukcja Obsługi Strona 81
- Strona / 169
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
Modulation Commands 6
U2761A Programmer’s Reference 73
[SOURce:]FM:STATe
Syntax
[SOURce:]FM:STATe {0|OFF|1|ON}
This command disables or enables the frequency modulation.
[SOURce:]FM:STATe?
This query returns the frequency modulation state as 0 if the modulation
is disabled, or 1 if the modulation is enabled.
Parameter
Remark
The U2761A allows only one modulation mode to be enabled at a time,
and does not allow modulation when sweep is enabled.
Examples
The following command enables the frequency modulation.
FM:STAT ON
The following query returns the modulation state.
FM:STAT?
Typical response:
1
Item Type Range of values Default value
state Boolean 0|OFF|1|ON 0
SOUR : FM space
?
0|OFF
1|ON
:STAT
- Agilent U2761A 1
- USB Modular 1
- Function/Arbitrary 1
- Waveform Generator 1
- Contents 3
- Instrument errors 152 7
- Self-test errors 153 7
- Calibration errors 153 7
- Arbitrary waveform errors 155 7
- Introduction to SCPI 9
- Mnemonic forms 10
- Command separators 11
- Using a comma ( , ) 12
- Using whitespace 12
- Using “?” commands 12
- Syntax conventions 13
- Square brackets “[ ]” 14
- Parenthesis “( )” 14
- Syntax diagram conventions 15
- Data types and formats 16
- Input message terminators 17
- Using device clear 18
- SCPI Status System 19
- 1 Introduction to SCPI 20
- Questionable Data register 21
- Standard Event register 22
- Status Byte register 23
- IEEE-488.2 Common Commands 25
- Parameter 27
- 2 IEEE-488.2 Common Commands 38
- APPLy Commands 39
- Using the APPLy Command 40
- APPLy:SINusoid 41
- APPLy:SQUare 42
- APPLy:RAMP 43
- APPLy:PULSe 44
- APPLy:DC 45
- APPLy:USER 46
- 3 APPLy Commands 48
- Output Configuration Commands 49
- [SOURce:]FUNCtion[:SHAPe] 50
- SOUR : FREQ space 52
- SOUR : VOLT space 53
- :LEV :IMM :UNIT VPP 58
- SOUR : FUNC space 59
- :SQU :DCYC percent 59
- :RAMP :SYMM percent 60
- OUTP :STAT space 61
- OUTP :LOAD space 62
- Pulse Configuration Commands 65
- SOUR : PULS space 66
- :PULS :HOLD WIDT 67
- :PULS :WIDT seconds 68
- :PULS :DCYC percent 70
- Modulation Commands 71
- [SOURce:]AM:INTernal:FUNCtion 72
- SOUR : AM space 74
- [SOURce:]FM:INTernal:FUNCtion 77
- SOUR : FM space 79
- SOUR : PM space 84
- Shift Keying Commands 87
- SOUR : ASK space 88
- SOUR : FSK space 90
- SOUR : PSK space 93
- 7 Shift Keying Commands 96
- Frequency Sweep Commands 97
- SOUR : SWE space 100
- :SPAC LIN 100
- Triggering Commands 103
- TRIG :SEQ space:SOUR IMM 104
- Examples 105
- TRIG :SEQ :IMM 106
- TRIG :SEQ space:SLOP POS 107
- OUTP :TRIG space:SLOP POS 108
- OUTP :TRIG space 110
- Arbitrary Waveform Commands 111
- DATA:DAC VOLATILE 112
- FORM space 114
- :BORD NORM 114
- DATA:ATTRibute:AVERage? 115
- DATA:ATTRibute:CFACtor? 116
- DATA :ATTR :POIN ? 117
- DATA:ATTRibute:PTPeak? 118
- SYSTem Commands 119
- SYSTem:CDEScription? 120
- SYSTem:ERRor? 121
- SYSTem:VERSion? 122
- Phase-Lock Commands 123
- SOUR : PHAS space:SOUR INT 124
- SOUR : PHAS space 125
- UNIT space 126
- :ANGL DEG 126
- SOUR : PHAS :REF 127
- :UNL :ERR :STAT 128
- OUTP :PHAS space 129
- 12 Phase-Lock Commands 130
- Status Reporting Commands 131
- STATus:PRESet 132
- STAT ?:QUES :COND 133
- STATus:QUEStionable:ENABle 134
- STAT :QUES ?:EVEN 136
- CALibration Commands 137
- CAL space:SEC OFF 138
- :STAT , code 138
- CAL space:SEC :CODE new code 139
- CALibration:SETup 140
- CAL space 141
- CAL :COUN ? 142
- 14 CALibration Commands 144
- CONFigure Command 145
- :SSI , @address , address( ) 146
- 15 CONFigure Command 148
- Error Messages 149
- Error Messages 16 151
- Execution errors 152
- 16 Error Messages 154
- Device-dependent errors 159
- Query errors 160
- Instrument errors 160
- Self-test errors 161
- Calibration errors 161
- Arbitrary waveform errors 163
- Factory Default Settings 165
- Factory Default Settings 17 167
- 17 Factory Default Settings 168
- Agilent Technologies 169
Powiązane produkty i podręczniki dla Nie Agilent Technologies AGILENT U2761A
Nie Agilent Technologies E1300B Dokumentacja
(78 strony)
(78 strony)
Nie Agilent Technologies Ininiium 90000 Dokumentacja
(134 strony)
(134 strony)
Nie Agilent Technologies U2802A Dokumentacja
(25 strony)
(25 strony)
© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.061 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji