Agilent Technologies U4154A Przewodnik Instalacji Pobierz pdf (Strona 3)

Safety Information

Agilent Technologies certifies that this

product met its published specifications at

the time of shipment from the factory. Agi-

lent Technologies further certifies that its

calibration measurements are traceable to

the United States National Institute of

Standards and Technology to the extent

allowed by that organization's calibration

facility, and to the calibration facilities of

other International Standards Organization

members.

Additional Information for Test and Mea-

surement Equipment

To comply with EMC regulations, supplied

or recommended cables must be used on

all appropriate connections. Otherwise, the

user has to ensure that, under operating

conditions, the Radio Interference Limits

are still met at the border of the user's

premises.

To ensure continued compliance to radi-

ated emissions standards, all RJ45 connec-

tions must be made using shielded

Category 5 (STP) cables.

Warnings

The following general safety precautions

must be observed during all phases of oper-

ation, service, and repair of this product.

Failure to comply with these precautions or

with specific warnings elsewhere in this

manual violates safety standards of design,

manufacture, and intended use of the prod-

uct. Agilent Technologies assumes no lia-

bility for the customer's failure to comply

with these requirements.

Before Applying Power Verify that all

safety precautions are taken. Make all con-

nections to the unit before applying power.

Note the instrument's external markings

described under "Safety Symbols".

Ground the Equipment: For safety, Class 1

equipment (equipment having a protective

earth terminal), an uninterruptible safety

ground must be provided from the mains

power source to the product input wiring

terminals or supplied power cable. Before

operating the equipment, guard against

electric shock in case of fault by always

using the provided 3-conductor power

cords to connect the equipment to a

grounded power outlet.

DO NOT use in hazardous environments:

Do not operate the product in an explosive

atmosphere or in the presence of flamma-

ble gases or fumes. This product is

designed for indoor use only.

Keep away from live circuits: Operating

personnel must not remove equipment cov-

ers or shields. Procedures involving the

removal of covers and shields are for use

by service-trained personnel only. Under

certain conditions, dangerous voltages may

exist even with the equipment switched

off. To avoid dangerous electrical shock, DO

NOT perform procedures involving cover or

shield removal unless you are qualified to

do so.

DO NOT operate damaged equipment:

Whenever it is possible that the safety pro-

tection features built into this product have

been impaired, either through physical

damage, excessive moisture, or any other

reason, REMOVE POWER and do not use

the product until safe operation can be ver-

ified by service-trained personnel. If neces-

sary, return the product to an Agilent

Technologies Sales and Service Office for

service and repair to ensure the safety fea-

tures are maintained.

DO NOT substitute parts or modify equip-

ment: Because of the danger of introducing

additional hazards, do not install substitute

parts or perform any unauthorized modifi-

cation to the product. Return the product to

an Agilent Technologies Sales and Service

Office for service and repair to ensure fea-

tures are maintained.

DO NOT clean with fluids: Doing so may

make the equipment unsafe for use. Power

down the equipment and disconnect the

power cord before cleaning. To clean, use a

soft dry cloth.

DO NOT block the primary disconnect: The

primary disconnect device is the appliance

connector/power cord when a chassis

used by itself, but when installed into a

rack or system the disconnect may be

impaired and must be considered part of

the installation.

Modules can become hot during use: DO

NOT touch any of the components on a

module as you remove it from the chassis.

Beware especially of the power module,

which is situated at the rear of the module.

Cautions

Do NOT block vents: To ensure adequate

cooling and ventilation, leave a gap of at

least 50mm (2") around all vent holes.

Do NOT operate with empty slots: To

ensure proper cooling and avoid damaging

equipment, fill any empty slots with the

AXIe filler panel module,

Do NOT stack free-standing chassis: For

benchtop use, do not stack chassis.

Stacked chassis should be rackmounted.

Exception—the bumpers, if installed on

both chassis, are designed to safely stack

one M9502A atop an M9502A or M9505A.

All RFI gaskets must remain in place: Any

damaged gaskets must be replaced.

All modules are grounded through the

chassis: During installation, tighten the

module’s retaining screws to secure the

module to the chassis and to make the

ground connection.

1 2 3 4 5 6 7 8 ... 67 68

Komentarze do niniejszej Instrukcji

Brak uwag

Agilent Technologies U4154A Przewodnik Instalacji Strona 3

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Multimetry Agilent Technologies U4154A