Agilent Technologies B2201A Podręcznik Użytkownika Strona 151
- Strona / 230
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
Agilent B2200 User’s Guide, Edition 4 5-23
SCPI Command Reference
:DIAGnostic:TEST:FRAMe:STATe?
Syntax :DIAGnostic:TEST:FRAMe[:EXECute]? CONTroller | FPANel |
LED | PEN | BEEPer
Query response test_result <newline><^END>
1: fail
0: pass
Example OUTPUT @Agb2200;":DIAG:TEST:FRAM? CONT"
:DIAGnostic:TEST:FRAMe:STATe?
This command returns the most recent test result (pass/fail) of the specified test.
Syntax :DIAGnostic:TEST:FRAMe:STATe? CONTroller | FPANel | LED
| PEN | BEEPer
Query response test_result <newline><^END>
1: fail
0: pass
-1: not tested
Parameter Explanation
CONTroller Controller test
FPANel Front panel interface test
LED LED matrix test
PEN Light pen test
BEEPer Beeper test
Parameter Explanation
CONTroller Controller test
FPANel Front panel interface test
LED LED matrix test
PEN Light pen test
BEEPer Beeper test
- Agilent B2200A 1
- Agilent B2201A 1
- Manual Part Number 2
- Warranty 2
- Technology Licenses 2
- Restricted Rights Legend 2
- Safety Summary 6
- Safety Symbols 8
- In This Manual 9
- Contents 11
- 1 Introduction 19
- Agilent B2200 Series 21
- Front Panel 22
- Introduction 23
- Figure 1-1 Front Panel View 23
- Rear Panel 24
- Figure 1-2 Rear Panel View 25
- Switch Modules 26
- Specifications 28
- General Specifications 29
- Accessories and Options 33
- 2 Installation 37
- Requirements 39
- Installation 40
- Operating Environment 41
- Inspection 42
- Installing the B2200 43
- To Set the GPIB Address 44
- To Connect the GPIB Cable 44
- To Install the Switch Module 45
- To Install the Blank Panel 45
- Self-Test 46
- Output Connections 47
- Connector Plates 48
- To Install Interlock Circuit 51
- To Install LED Circuit 52
- Cathode(-) 53
- Anode(+) 53
- To Mount Connectors 54
- 2 − ∅11.3 ∅3.2 2 − M3 x 0.5 55
- 14 11 11 14 55
- Input Connections 56
- Measurement Cable Length 59
- Maintenance 61
- 3 Front Panel Operation 63
- Operation 65
- To Initialize Agilent B2200 66
- To Enable Light Pen 66
- To Change Connection Rule 67
- To Change Connection Sequence 67
- To Control Switch Condition 67
- To save the setup 68
- To load the setup 68
- To Use Bias Mode 69
- To Use Ground Mode 70
- To Use Couple Mode 71
- To Display Firmware Revision 71
- To Display Module Information 71
- To clear error buffer 72
- LED matrix 73
- Switch Control Functions 74
- Channel Configuration Mode 75
- Connection Rule 76
- Connection Sequence 77
- Bias Mode 78
- Ground Mode 80
- Couple Mode 82
- Display Functions 84
- SequenceRule 85
- GndLock Error GndBias 85
- Card Selection key 86
- Function Edit 87
- Function key group 88
- Break_Before_Make 89
- Settings: 01 [ ] 89
- SET VIEW 90
- ENABLE DISABLE 90
- Channel: 01 90
- Channel: No Channel 90
- Channel 01: ENABLED 90
- Setup Menus 92
- Selftest Menu 96
- Enter key 97
- Exit key to return to the 97
- 4 Programming 101
- :ROUT:CONN:RULE ALL,FREE 103
- :ROUT:CONN:SEQ ALL,BBM 103
- Fundamental Commands 104
- Switch Control 105
- Programming Examples 107
- Connecting Input-Output Paths 108
- Using Bias Mode 110
- Using Ground Mode 112
- Using Couple Mode 114
- Saving Input/Output Labels 116
- Capacitance Compensation 120
- Required Conditions 121
- FORCE or SENSE (A) 126
- FORCE or SENSE (B) 126
- Insulator 126
- Triaxial Cable 126
- 5 SCPI Command Reference 129
- Common Commands 132
- Subsystem Commands 141
- SCPI Command Reference 142
- Command Summary 142
- Relay Control Commands 142
- Command Description 142
- Bias Mode Commands 143
- Ground Mode Commands 144
- Couple Mode Commands 145
- :DIAGnostic:TEST:CARD:CLEar 149
- :DIAGnostic:TEST:CARD:STATe? 149
- :DIAGnostic:TEST:FRAMe:CLEar 150
- ENTER @Agb2200;A$ 153
- [:ROUTe]:AGND:PORT 154
- [:ROUTe]:AGND[:STATe] 155
- [:ROUTe]:AGND:UNUSED 156
- [:ROUTe]:BIAS:PORT 159
- [:ROUTe]:BIAS[:STATe] 160
- [:ROUTe]:CLOSe:CARD? 161
- [:ROUTe]:CLOSe[:LIST] 161
- [:ROUTe]:CONNection:RULE 162
- [:ROUTe]:CONNection:SEQuence 162
- [:ROUTe]:COUPle:PORT 163
- [:ROUTe]:COUPle:PORT:DETect 164
- [:ROUTe]:COUPle[:STATe] 165
- [:ROUTe]:FUNCtion 166
- [:ROUTe]:OPEN:CARD 166
- [:ROUTe]:OPEN[:LIST] 167
- [:ROUTe]:SYMBol:CHANnel 167
- [:ROUTe]:SYMBol:PORT 168
- :SYSTem:BEEP 169
- :SYSTem:CCONfig? 169
- :SYSTem:CDEScription? 170
- :SYSTem:CPON 171
- :SYSTem:CTYPe? 172
- :SYSTem:DISPlay:LCD 172
- :SYSTem:DISPlay:LED 173
- :SYSTem:DISPlay:STRing 173
- :SYSTem:ERRor? 174
- :SYSTem:KLC 174
- :SYSTem:MEMOry:COMMent 175
- :SYSTem:MEMOry:DELete 175
- :SYSTem:MEMOry:LOAD 176
- :SYSTem:MEMOry:SAVE 176
- :SYSTem:PEN 177
- :SYSTem:VERSion? 177
- Status Reporting Structure 178
- Status Byte Register 180
- Output Queue 185
- 6 VXIplug&play Driver 187
- System Requirements 189
- Driver Functions 191
- VXIplug&play Driver 216
- 7 Error Messages 217
- Standard SCPI Error Messages 219
- Execution Error 223
- Device-Dependent Errors 224
- Query Errors 225
- B2200 Channel Related Errors 227
Powiązane produkty i podręczniki dla Multimetry Agilent Technologies B2201A
Multimetry Agilent Technologies 8481B Dokumentacja
(154 strony)
(154 strony)
(164 strony)© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.047 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji