Agilent Technologies 8487D Podręcznik Użytkownika Strona 166
- Strona / 196
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
Error Messages
Error Messages
4-8 Agilent E4418B User’s Guide
-230 Data corrupt or stale;Please zero and calibrate Channel A
When CAL[1|2]:RCAL is set to ON and the sensor currently connected
to channel A has not been zeroed and calibrated, then any command
which would normally return a measurement result (for example
FETC?, READ?, or MEAS?) will generate this error message.
-230 Data corrupt or stale;Please zero Channel A
When CAL[1|2]:RCAL is set to ON and the sensor currently connected
to channel A has not been zeroed, then any command which would
normally return a measurement result (for example FETC?, READ?, or
MEAS?) will generate this error message.
-230 Data corrupt or stale;Please calibrate Channel A
When CAL[1|2]:RCAL is set to ON and the sensor currently connected
to channel B has not been calibrated, then any command which would
normally return a measurement result (for example FETC?, READ?, or
MEAS?) will generate this error message
-231 Data questionable;CAL ERROR
Power meter calibration failed. The most likely cause is attempting to
calibrate without applying a 1 mW power to the power sensor.
-231 Data questionable;Input Overload
The power input to Channel A exceeds the power sensor’s maximum
range.
-231 Data questionable;Lower window log error
This indicates that a difference measurement in the lower window has
given a negative result when the units of measurement were
logarithmic.
-231 Data questionable;Upper window log error
This indicates that a difference measurement in the upper window has
given a negative result when the units of measurement were
logarithmic.
-231 Data questionable;ZERO ERROR
Power meter zeroing failed. The most likely cause is attempting to zero
when some power signal is being applied to the power sensor.
HP4402.book Page 8 Wednesday, November 29, 2000 4:46 PM
- User’s Guide 1
- Legal Information 3
- Limitation of Warranty 4
- Exclusive Remedies 4
- Equipment Operation 5
- General Safety Considerations 6
- IEC 1010-1 Compliance 7
- Statement of Compliance 7
- User Environment 7
- Installation Instructions 7
- Regulatory Information 8
- Declaration of Conformity 9
- List of Related Publications 10
- Available Accessories 11
- About this Guide 12
- Table of Contents 13
- List of Figures 17
- List of Tables 19
- Getting Started 21
- Turning On the Power Meter 23
- The Front Panel at a Glance 24
- The Display Layout 27
- Selecting Your Display Layout 31
- Window Symbols 34
- 1 of N Entry Window 35
- The Rear Panel at a Glance 36
- Adjusting the Carrying Handle 38
- Rack Mounting the Power Meter 39
- General Information 43
- Running Time 43
- Charging Times 44
- Backlight 44
- Battery Removal/Replacement 45
- Zeroing the Power Meter 47
- Zero/Cal Lockout 47
- Calibrating the Power Meter 48
- 1 2 3 4 5 6 7 8 52
- Power Sensors 55
- Making the Measurement 60
- Offset Tables 67
- Making Relative Measurements 74
- Setting the Resolution 75
- Setting Offsets 76
- Setting Averaging 78
- Step Detection 79
- Measuring Pulsed Signals 81
- Setting Measurement Limits 83
- Setting Window Limits 84
- Checking for Limit Failures 87
- Setting the Range 92
- RS232/RS422 94
- Remote Interface Overview 96
- Recorder Output 99
- Leveling a Source Output 100
- Power Meter Operation 101
- Lower Window 103
- Presetting the Power Meter 104
- Self Test 106
- Remote Testing 109
- Test Descriptions 110
- Operator Maintenance 113
- Check the Basics 115
- Instrument serial numbers 115
- GB12345678 116
- Sales and Service Offices 117
- Latin America: 118
- United States: 118
- Menu Reference 121
- Introduction 122
- The Front Panel Menu Maps 123
- Frequency/Cal Fac Menu 124
- Meas Setup Menu 125
- Rel/Offset Menu 126
- Save/Recall Menu 126
- System Inputs Menu (1 of 4) 127
- System Inputs Menu (2 of 4) 128
- System Inputs Menu (3 of 4) 129
- System Inputs Menu (4 of 4) 130
- Zero/Cal Menu 131
- Front Panel Menu Reference 132
- Frequency 133
- TTL Inputs Off On 155
- Diagrammatical Hardkeys 156
- Error Messages 159
- Specifications 171
- Power Meter Specifications 173
- Accuracy 174
- Power Reference 175
- Measurement Speed 176
- Zero Drift of Sensors 177
- Measurement Noise 177
- Settling Time 179
- Power Sensor Specifications 182
- General Characteristics 184
- Environmental Characteristics 185
- Dimensions 186
- Remote Programming 186
- Non-Volatile Memory 187
- 3-19, 3-26 192
Powiązane produkty i podręczniki dla Multimetry Agilent Technologies 8487D
(6 strony)© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.049 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji