Agilent Technologies 16440A Instrukcja Obsługi Pobierz pdf (Strona 68)

Module 7

Measurement Functions

7-48

SMU1 Function to VAR1

Vh = 0 to 2.5 V

Bias Hold to ON

Output Value to STOP

Bias Hold Exercise

Channel and Measurement Setup

Set the SMU1 Function to VAR1. The VAR1 output 0 to 2.5 V is enough to light the LED.

Set the Bias Hold after Measurement field to ON to enable the bias hold function. And set the

Output Value after Measurement field to STOP. This setup keeps 2.5 V output between sweep

measurements. So the LED can light between the measurements.

1 2 ... 63 64 65 66 67 68 69 70 71 72 73 ... 135 136

Agilent B1500A 1
Semiconductor Device 1
Analyzer 1
Manual Part Number 2
Warranty 2
Technology Licenses 2
Restricted Rights Legend 2
In This Manual 4
Class Exercises 6
Demo.xpg file 7
.xtd files 7
.xtr files 7
1 ohm Resistor 10
1.1 kohm Resistor 10
511 kohm Resistor 10
0.1 uF Capacitor 10
Module 1. Introduction 13
Module 2. Getting Started 13
Module 5. Basic Measurement 15
Contents 20
Contents-8 20
7 Measurement Functions 21
In This Module 22
SMU Pulsed Sweep Measurement 23
SMU Pulse Mode 24
VAR1 Sweep 24
Pulse On Primary Source 25
Hints on Pulsing the HPSMU 26
Limitations 27
SMU Triax Connection 29
Jumper Leads – MOS transistor 30
Data Display Window 31
Drain pulse 32
Enter new name before save 32
Channel Setup 32
Measurement Setup 33
I/V-t Sampling Measurement 34
Sampling Measurement 36
Module 7 37
Measurement Functions 37
RC Measurement 38
10 data/decade 39
Variable for time data 40
Sampling Exercise 40
High speed ADC 41
FIXED range 41
Bias starts at 0 s 42
Negative Hold Time 42
Interval < 2 ms 44
Current source 44
Channel and Measurement Setup 44
Auto Analysis 45
Vth Example 46
Vth Measurement 47
Damaged MOS FET Device? 49
Function Setup 51
Display Setup Page 52
Analysis Setup Page 53
SMU Filter 54
SMU Filter: ON (add filter) 55
SMU Series Resistor 56
0.5 M ohm (device only) 59
Series R: 1MOHM (add 1 M ohm) 60
Calculated value 62
Compensation 62
Standby Function 63
To Use Standby Function 64
Bias Hold After Measurement 65
Bias Hold Function 66
Bias Hold Exercise 68
Repeat Measurement Setup 69
LED lights on 70
LED lights off 70
8 Capacitance Measurement 71
B1500A Multi Frequency CMU 73
CMU Block Diagram 74
C-V Sweep Source 75
C-V Sweep Measurement 76
Cable Connections 77
Conductance 79
Capacitance Measurement 79
Measurement Example 79
CMU Calibration 81
Calibration 82
Opens dialog box to start 82
SCUU – for IV/CV Switching 83
Module 8 84
GSWU Connection Example 87
ASU – for IV/CV Switching 88
Configuration 90
ASU Switch Control 90
Modification Overview 93
To Modify Test Definition 100
Test Definition editor 100
Variable Yes is used in 101
Class Exercise 104
To Use Debug Tools 105
Break point 105
ReturnPort = SMU1 105
ReturnCh = OUT1 105
Variable Inspector 105
Debug: Inspect button 107
Paused point 107
Module 9 109
To Use Built-in Functions 110
To Use Read Out Functions 112
Vth = @L1X 113
To Add Data Display 114
To Use Auto Analysis Function 116
Data Display: OFF/ON 117
Data Store: OFF/ON 117
Assign to external variables… 118
Setup example 119
Result example 120
Using built-in functions 121
To use Auto Analysis twice 124
Auto Analysis Setup 128
Check this box 128
To Set Display Setup 129
Display Setup 129
Idrain=Id@Vth*Polarity 130
To Use Auto Analysis Twice 131
Setting vector data 135

Komentarze do niniejszej Instrukcji

Brak uwag

Agilent Technologies 16440A Instrukcja Obsługi Strona 68

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Pomiary, testowanie i kontrola Agilent Technologies 16440A