Agilent-technologies InfiniiVision 6000 Series Instrukcja Użytkownika Pobierz pdf (Strona 17)

Performance characteristics (continued)

Vertical system: scope channels (continued)

Noise peak-to-peak MSO/DSO601xA: 3% full scale or 2 mV, whichever is greater

MSO/DSO603xA: 3% full scale or 3 mV, whichever is greater

MSO/DSO605xA: 3% full scale or 3.6 mV, whichever is greater

MSO/DSO610xA: 3% full scale or 4 mV, whichever is greater

DC vertical gain accuracy*

±2.0% full scale

DC vertical offset accuracy ≤200 mV/div: ±0.1 div ±2.0 mV ±0.5% offset value;

>200 mV/div: ±0.1 div ±2.0 mV ±1.5% offset value

Single cursor accuracy

±{DC vertical gain accuracy + DC vertical offset accuracy + 0.2% full scale (~1/2 LSB)}

Example: for 50 mV signal, scope set to 10 mV/div (80 mV full scale), 5 mV offset,

accuracy = ±{2.0% (80 mV) + 0.1 (10 mV) + 2.0 mV + 0.5% (5 mV) + 0.2%(80 mV)} = ± 4.785 mV

Dual cursor accuracy*

±{DC vertical gain accuracy + 0.4% full scale (~1 LSB)}

Example: for 50 mV signal, scope set to 10 mV/div (80 mV full scale), 5 mV offset,

accuracy = ±{2.0% (80 mV) + 0.4% (80 mV)} = ±1.92 mV

* Denotes warranted specifications, all others are typical. Specifications are valid after a 30-minute warm-up period and ±10 °C from firmware calibration temperature.

1 1 mV/div is a magnification of 2 mV/div setting for 100 MHz models and 2 mV/div is a magnification of 4 mV/div setting for 300 MHz - 1 GHz models. For vertical accuracy

calculations, use full scale of 16 mV for 1 mV/div sensitivity setting and 32 mV for 2 mV/div sensitivity setting.

Vertical system: logic channels (MSO6000A or MSO-upgraded DSO6000A only)

Number of channels 16 logic timing channels – labeled D15 - D0

Threshold groupings Pod 1: D7 - D0

Pod 2: D15 - D8

Threshold selections TTL, CMOS, ECL and user-definable (selectable by pod)

User-defined threshold range ±8.0 V in 10 mV increments

Maximum input voltage ±40 V peak CAT I; transient overvoltage 800 Vpk

Threshold accuracy* ±(100 mV + 3% of threshold setting)

Input dynamic range ±10 V about threshold

Minimum input voltage swing 500 mV peak-to-peak

Input capacitance ~8 pF

Input resistance 100 kΩ ±2% at probe tip

Channel-to-channel skew 2 ns typical, 3 ns maximum

* Denotes warranted specifications, all others are typical. Specifications are valid after a 30-minute warm-up period and ±10 °C from firmware calibration temperature.

1 2 ... 12 13 14 15 16 17 18 19 20 21 22 ... 27 28

Komentarze do niniejszej Instrukcji

Brak uwag

Agilent-technologies InfiniiVision 6000 Series Instrukcja Użytkownika Strona 17

Komentarze do niniejszej Instrukcji