Agilent Technologies 8922S Dokumentacja Strona 130
- Strona / 244
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
11-2
Self-Test Error Messages
Introduction
Introduction
This chapter lists the error messages that appear on the status line of the display and on the
message screen when the self-tests are run on power-up. This list does not include all of
the messages that can appear under all circumstances.
”Battery Backed RAM Initialized. Structures corrupt.”
”Battery Backed RAM Initialized. Option RAM not maintained.”
”Battery Backed RAM Initialized.Optional RAM not found.”
”Battery Backed RAM Initialized. Standard RAM not maintained.”
”All host processor self-tests passed.”
”PANIC - UNKNOWN ERROR OCCURRED.”
”Attempt to write EEPROM failed.”
”Communication failure with the Rcvr Step Loop Board.”
A serial communications failure occurred with the A17 Step Loop assembly.
”Communication failure with the Sig Gen Step Loop Board.”
A serial communications failure occurred with the A26 Step Loop A assembly.
”Communication failure with the NSM/PMF Board.”
A serial communications failure occurred with the A5 Premod Filter and NSM assembly.
”Hop Controller communication channel Failure.”
”Self-test failure in Hop Controller.”
The A33 Hop Controller assembly failed its self-test.
”Hop Controller did not post self-test results.”
”DSP Analyzer communication Channel Failure.”
”Self-test failure in DSP Analyzer.”
The A9 Global Test and Demod assembly failed its self-test
”DSP Analyzer did not post self-test results.”
”Protocol Processor Communication Channel Failure.”
”Self-test failure in Protocol Processor.”
The A32 GSM Controller assembly failed its self-test.
- Assembly Level Repair 1
- HP/Agilent Technologies 1
- 8922 Series GSM Test Set 1
- Contents 10
- Localizing the Problem 11
- Introduction 12
- Power-Up Checks 14
- If Power-Up Checks FAILED 15
- Where to Go Next 21
- Running Diagnostics 27
- Loading the RAM Test 33
- Verifying Performance 35
- HP/Agilent 8922F/H or M/S 37
- To Run the Program 38
- Notes on Running the Program 38
- Configuring the RF Extender 41
- Configuring the RF Extender 42
- Extending Modules 43
- Making Measurements 44
- Parallel Bus 49
- Serial Bus 50
- Keyboard 52
- Power Cord Verification 57
- Power Cord Verification 58
- Transformer / Power Switch 60
- Where To Go Next 62
- Adjustments and Calibration 63
- Timebase Adjustments 65
- Periodic Calibrations 67
- Sum Loop Adjustment Procedure 68
- Second Adjustment 69
- Final Adjustment 69
- Final Check 69
- Top and Bottom Cover Removal 73
- Inside Protective Covers 74
- A1 Front Panel Removal 77
- Tools Required 79
- A11 Receiver Mixer Removal 80
- A12 Pulse Attenuator Removal 82
- A21 GPIB Interface Removal 84
- A22 Display Removal 86
- A23 Input Section Removal 88
- A24 Attenuator Removal 89
- A28 Power Supply Removal 90
- Fan Removal 92
- Transformer Removal 94
- Replacing a Part 100
- Replaceable Parts 100
- Firmware Upgrades 123
- Service Screen 125
- Self-Test Error Messages 129
- Module I/O Specifications 131
- A2 Audio Analyzer 2 133
- Module I/O Specifications 134
- A3 Audio Analyzer 1 135
- A4 Modulation Distribution 138
- Power Supplies 140
- Serial I/O 142
- A6 Signaling Source/Analyzer 143
- A9 Global Test and Demod 145
- A11 Receiver Mixer 149
- A13 Output 152
- A14 Pulse Driver 154
- A15 Reference 156
- Hop Control 157
- A16 Receiver 162
- A18 Spectrum Analyzer 166
- A19 Measurement 168
- A25 Sum Loop 180
- A17, A26 Step Loop 183
- A27 DAC/Upconverter 186
- A28 Power Supply 188
- A33 Hop Controller 189
- Instrument Block Diagrams 193
- Block Diagram 3 195
- Block Diagram 4 195
- Block Diagram 5 195
- Technical Discussion 199
- Block Diagram 1 200
- A17 StepLoop B 201
- A18 Spectrum Aanalyzer 203
- Block Diagram 2 205
- A26 Step Loop A 207
- A12 Pulse Attenuator 209
- A23 Input 209
- A24 High Power Attenutor 209
- HP/Agilent 8922B Only 211
- A37 Sequence Controller 212
- Diagnostics Theory 215
- AF_DIAGS 217
- Audio Analyzer 2 218
- RF_DIAGS 219
- RF Generator Step Loop 220
- Sum Loop 220
- Output Section 220
- Pulse Attenuator and Drive 221
- Input Section 221
- RF Analyzer Step Loop 222
- Spectrum Analyzer 223
- Receiver 223
- MS_DIAGS 225
- GSM and DCS Diagnostic Tests 226
- Interpreting Results 227
- Measurement Theory 229
- GSM Theory 235
- The GSM System 237
- Numerics 239
Powiązane produkty i podręczniki dla Networking Agilent Technologies 8922S
Networking Agilent Technologies E6392B Dokumentacja
(197 strony)
(197 strony)
Networking Agilent Technologies 8753ES Dokumentacja
(204 strony)
(204 strony)
© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.041 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji