Agilent Technologies 86100C Instrukcja Użytkownika Pobierz pdf (Strona 15)

Multimode and single-mode 86101A 86102A 86102U

OPTICAL CHANNEL SPECIFICATIONS

Optical channel unfiltered bandwidth 2.85 GHz (3 GHz typical) 10 GHz 15 GHz

Wavelength range 750 to 860 nm

Calibrated wavelengths 850 nm

Optical sensitivity

–17 dBm –13.5 dBm –7.5 dBm

Transition time (10% to 90% calculated from TR = 0.48/BW optical)

Unfiltered 160 ps 48 ps 32 ps

RMS noise

Characteristic 1.5 µW 3.4 µW 14 µW

Maximum 2.5 µW 5.5 µW 20 µW

Scale factor (per division)

Minimum 5 µW 20 µW

Maximum 100 µW 500 µW

CW accuracy (single marker, referenced to ±6 µW ±0.4% of full scale ±25 µW ±2% of (reading-channel

average power monitor, <50 µW/division) ±3% of (reading-channel offset) offset), 15 GHz

CW offset range (referenced two divisions

from screen bottom) +0.2 mW to –0.6 mW +1 mW to –3 mW

Average power monitor

(specified operating range) –30 dBm to –2.2 dBm –30 dBm to –2.2 dBm –27 dBm to +3 dBm

Factory calibrated accuracy ±5% ±100 nW ±connector uncertainty, 20 °C to 30 °C

User calibrated accuracy ±2% ±100 nW ±power meter uncertainty, < 5 °C change

Maximum input power

Maximum non-destruct average 0.4 mW (–4 dBm) 0.8 mW (–1 dBm) 2 mW (+3 dBm)

Maximum non-destruct peak 10 mW (+10 dBm)

Fiber input 62.5/125 µm, user selectable connector

Input return loss

(HMS-10 connector fully filled fiber) 20 dB

ELECTRICAL CHANNEL SPECIFICATIONS

Electrical channel bandwidth 12.4 and 20 GHz

Transition time 28.2 ps (12.4 GHz)

(10% to 90%, calculated from TR = 0.35/BW) 17.5 ps (20 GHz)

RMS noise 0.25 mV (12.4 GHz)

Characteristic 0.5 mV (20 GHz)

Maximum 0.5 mv (12.4 GHz)

1 mV (20 GHZ)

Scale factor

Minimum 1 mV/division

Maximum 100 mV/division

DC accuracy (single marker) ±0.4% of full scale ± 2 mV ±1.5% of (reading-channel offset), 12.4 GHz

±0.4% of full scale ± 2 mV ±3% of (reading-channel offset), 20 GHz

DC offset range (referenced to center of screen) ±500 mV

Input dynamic range (relative to channel offset) ±400 mV

Maximum input signal ±2 V (+16 dBm)

Nominal impedance 50 Ω

Reflections (for 30 ps rise time) 5%

Electrical input 3.5 mm (male)

Module specifications: single-mode

& multimode optical/electrical

Smallest average optical power required for mask test. Values represent typical sensitivity

of NRZ eye diagrams. Assumes mask test with complicance filter switched in.

1 2 ... 10 11 12 13 14 15 16 17 18 19 20 ... 23 24

Komentarze do niniejszej Instrukcji

Brak uwag

Agilent Technologies 86100C Instrukcja Użytkownika Strona 15

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Pomiary, testowanie i kontrola Agilent Technologies 86100C