Agilent Technologies 222A Instrukcja Obsługi Pobierz pdf (Strona 89)

3Specifications

In this chapter you will find the specifications of the Agilent 81101A

Pulse Generator.

At the end of this chapter, “Pulse Parameter Definitions” on page 105

provides detailed information on the definition of the pulse parameters

used by the instrument.

NOTE Warranted Performance

Specifications describe the instrument’s warranted performance. Non-

warranted values are described as typical. All specifications apply after a

30 minute warm-up phase with 50 Ohm source, a 50 Ohm load resistance

and separate channels. They are valid from 0

C to 55

C ambient

temperature.

1 2 ... 84 85 86 87 88 89 90 91 92 93 94 ... 122 123

Reference Guide 1
Agilent 81101A 50 MHz 3
Pulse Generator 3
Copyright 4
Warranty 4
Limitation of Warranty 5
Exclusive Remedies 5
Certification 5
Services and Support 5
Safety Summary 6
Ground the Instrument 7
Safety Symbols 8
About this Book 9
Conventions Used in this Book 10
Contents 11
1General Programming 13
The GP-IB Interface Bus 14
Agilent 81101A Remote Control 15
Programming Recommendations 16
Common Command Summary 18
Status Model 19
Condition Register 20
Transition Filters 20
Event Register 20
Enable Register 21
Status Byte 22
Standard Event Status Group 22
OPERation Status Group 23
QUEStionable Status Group 24
2Programming Reference 25
Agilent 81101A SCPI Command 26
Programming Reference 31
Programming the Instrument 35
Continuous 36
Triggered 36
External Width 37
SCPI Instrument Command List 38
:DISPlay[:WINDow][:STATe] 43
DISP OFF 43
:MMEMory:CATalog? 44
:MMEMory:CDIRectory 44
:MMEMory:COPY 45
:MMEMory:DELete 45
:MMEMory:INITialize 45
:MMEMory:LOAD:STATe 46
:MMEMory:STORe:STATe 46
:OUTPut[1][:NORMal][:STATe] 47
:OUTP ON 47
:OUTPut[1]:IMPedance:EXTernal 47
:OUTPut[1]:POLarity 48
Amplitude = High – Low 50
Offset = 50
High – Low 50
Period = 54
Frequency 54
[:SOURce]:HOLD 55
[:SOURce]:PHASe[1][:ADJust] 56
[:SOURce]:PULSe:DCYCle[1] 57
[:SOURce]:PULSe:DELay[1] 57
[:SOURce]:PULSe:DELay[1]:HOLD 58
[:SOURce]:PULSe:DELay[1]:UNIT 59
DblDel% = 60
Frequency = 62
[:SOURce]:PULSe:PERiod:AUTO 63
[:SOURce]:PULSe:TDELay[1] 63
[:AMPlitude] 67
[:SOURce]:PULSe:WIDTh[1] 68
[:SOURce]:ROSCillator:SOURce 68
Amplitude 70
Offset = 72
High–Low 73
:STATus:PRESet 76
:SYSTem:CHECk[:ALL][:STATe] 78
:SYSTem:ERRor? 78
:SYSTem:KEY 79
:SYSTem:PRESet 81
:SYSTem:SECurity[:STATe] 82
:SYSTem:SET 83
:SYSTem:VERSion? 83
:SYSTem:WARNing[:COUNt]? 83
:SYSTem:WARNing:STRing? 84
:SYSTem:WARNing:BUFFer? 84
:TRIGger[:SEQuence[1]]:COUNt 84
:TRIGger:IMPedance 85
:TRIGger:LEVel 86
:TRIGger:SLOPe 86
3Specifications 89
Manufacturer 90
Supplementary 90
Information 90
Agilent 81101A Specifications 91
Recalibration period 92
Acoustic Noise Emission 92
Timing Specifications 93
Transition Times 95
Level Specifications 96
Clock Sources 97
Clock / PLL Reference Input 98
Phase Locked Loop (PLL) 98
Output Modes 99
Trigger Modes 100
Trigger Output 101
Strobe Output 101
Typical Delays 102
Human Interface 103
Remote Control 104
Pulse Parameter Definitions 105
Time Reference Point 106
Pulse Period 106
Trigger Delay 106
Pulse Width 106
Pulse Delay 107
Double Pulse Delay 107
Interchannel Delay (Skew) 107
Transition Time 108
Linearity 108
Stability 109
Pulse Levels 109
Preshoot, Overshoot, Ringing 110
Settling Time 110
Repeatability 111
Specifications 112
Front Panel Controls 117
Edition E0300 118
Printed in Germany 118
81101-91021 118
DECLARATION OF CONFORMITY 123

Komentarze do niniejszej Instrukcji

Brak uwag

Agilent Technologies 222A Instrukcja Obsługi Strona 89

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Pomiary, testowanie i kontrola Agilent Technologies 222A